PixaromaHelp
Help › Nodes › Image

Seamless Tile Pixaroma

Makes the picture repeat with no edge, every time.

In ComfyUI: double-click an empty spot on the canvas and type Seamless Tile Pixaroma.

What it does

A seamless pattern or texture has to join on all four sides: its right edge continues into its left edge, its bottom edge into its top edge. Newer models never learned that, so you only get it on a lucky seed.

This node changes the model and the VAE so the picture they make has no edge at all. It joins on every seed, with any prompt. Same speed, nothing downloaded, and the loaded models are not changed: it works on a copy inside the run.

Where it goes

Wire the model (after any LoRA loaders) and the VAE into it. Then use its model output in the KSampler and its vae output in VAE Decode. Both matter: the model makes a picture that joins, the VAE keeps the edge clean when it turns it into pixels. A normal VAE leaves a faint line. A node that rebuilds the VAE (VAE Compute Dtype, a MultiGPU VAE loader) goes before this node, never after it.

Add Seamless Preview Pixaroma after VAE Decode to see the repeat and get a PASS / FAIL check.

Tile

Both
Joins in every direction. For patterns and textures.
Left and right
Only the left and right edges join: a strip that repeats sideways, like a border or a panorama loop.
Up and down
Only the top and bottom edges join.
Off
The model and VAE pass through unchanged, to compare with and without.

Models and sizes

Works with Krea 2, Z-Image, FLUX.2 Klein (4B and 9B), FLUX 3 Klein, SDXL and SD 1.5, text to picture. Any other model stops the Run with a message instead of silently making a picture that does not join. FLUX.2 [dev] shares Klein's design and runs too, but was not tested. Qwen Image 2.1 was tested and left out: its patterns joined but lost their big motifs.

The width and height must be multiples of 16 px (32 px for SDXL, 64 px for SD 1.5), or the Run stops and names a size that works. Krea 2 looks best at 1536 x 1536; at 1024 its motifs come out a little smaller and more regular. Z-Image, FLUX.2 Klein and FLUX 3 Klein are good at 1024.

Prompts

The node makes the edges join, the prompt makes the picture worth repeating. Describe a flat, evenly spread pattern or a texture seen straight from above with flat light. Words like centered, vignette, depth of field or cinematic work against a repeat. AI Prompt Pixaroma has presets for this: "Seamless pattern - prompt from an idea" for any pattern or material, "Seamless textile print" for fabric and wallpaper prints, and "Seamless game texture" for floors, walls and panels in games and 3D. Type a few words (candy cane, oak wood, ditsy floral, sci-fi floor) and it writes the prompt. To get something like a pattern you already have, use "Seamless pattern - prompt from an image": wire in the picture (a print on a cushion or a dress works too) and type any changes, such as "with cats".

The hardest case is long straight diagonal stripes across the whole picture, like candy cane stripes: the edges still join, but the model may bend the stripes or shift them halfway to make them meet. Horizontal and vertical stripes, plaid, chevrons, waves and small angled motifs (tossed candy canes) come out clean.

Low memory

If the card has too little memory for one VAE decode, ComfyUI decodes in tiles. The edges are then wrapped around before decoding: very close to seamless but not exact. The console says so, and Seamless Preview's check shows the result.

Licences and credit

The picture is yours, but the model's licence still applies: Krea 2 is free for companies under US$1M a year, Z-Image is Apache-2.0, and the FLUX models each have their own licence, so read it before you sell what you make. The idea of snapping the position code to the tile follows the SpheRoPE paper (Hirschorn et al., 2026); the code is our own.

What you wire in

modelMODEL
The model, after any LoRA loaders. Krea 2, Z-Image, FLUX.2 Klein, FLUX 3 Klein, SDXL or SD 1.5.
vaeVAE
The VAE that decodes the picture. Use the vae output of this node in VAE Decode, or the picture gets a faint line at the edges.

The settings on the node

tilechoicedefault Both
Which edges join. Both = repeats in every direction (patterns, textures). Left and right = a strip that repeats sideways. Up and down = repeats vertically. Off = the model and VAE pass through unchanged.
BothLeft and rightUp and downOff

What comes out

modelMODEL
The model that makes pictures with no edge. Connect it to the sampler.
vaeVAE
The VAE that decodes with no edge. Connect it to VAE Decode.
Text to picture only. A video model, a reference image, area prompts or a tiled upscaler (Ultimate SD Upscale) are not supported yet.

This is the help that comes with Pixaroma 1.4.261. Inside ComfyUI, select the node and click the orange ? above it to read the same help there.